What Causes Fatigue Fracture Of Bolts? Understand The Failure Mechanism
Nov 20, 2026
At assembly sites for wind power, steel structures, automated equipment and curtain wall projects, a puzzling failure often occurs: a bolt suddenly fractures after a period of service, even though its static tensile load is far below its tensile strength.
This fracture is not a one-time overload breakage, but a typical fatigue fracture. It is highly concealed and likely to cause equipment shutdowns and structural safety accidents. It is also a key failure type that engineering purchasers and assembly engineers focus on.
1. What is Bolt Fatigue Fracture?
Fatigue fracture is a failure mode where tiny cracks gradually expand under repeated alternating loads until brittle fracture occurs.
It differs from overload fracture: overload fracture happens when a one-time massive external force directly snaps the bolt, with obvious plastic deformation and necking on the fracture surface. By contrast, fatigue fracture usually comes without obvious deformation, occurs abruptly, and shows almost no visible warning signs in the early stage.
The whole process includes three stages: crack initiation → slow crack propagation → instantaneous fracture. In most cases, cracks originate at stress concentration locations such as thread roots and are hard to detect in advance.
2. Core Inducements of Bolt Fatigue Fracture
Stress Concentration (The Most Common Root Cause) The thread root bears the highest stress on a bolt and is where fatigue cracks most easily initiate. The thread root is a circular transition zone. If the root radius is too small, machining tool marks remain, or scratches and dents occur, stress will concentrate at this spot. Under repeated alternating loads, tiny notches will gradually develop into fatigue cracks.
Besides, the junction between bolt head and shank, relief grooves, surface scratches and material inclusions are all high-risk positions for stress concentration.
Improper Preload Control Two unfavorable preload conditions can both trigger fatigue failure: Insufficient preload: The bolt is subjected to alternating tensile loads repeatedly during operation. Slippage occurs between the bolt and clamped parts, causing continuous load fluctuation and accelerating fatigue crack propagation. Excessive preload: The bolt stays under high stress for a long time, leaving a greatly reduced fatigue margin. Minor load fluctuations can trigger fatigue failure. High-strength bolts have a specified preload range; tighter does not mean safer.
Continuous Alternating Loads A bolt qualified under static load cannot withstand repeatedly changing loads. Loads change periodically on vibrating equipment, wind turbine towers, vehicle chassis and conveying equipment. Even if each individual load is small, fatigue failure will eventually occur once the material's fatigue limit is exceeded after countless cycles. Fatigue failure depends not on the magnitude of a single load, but on the number of load cycles.
Material and Heat Treatment Defects Internal inclusions, porosity and segregation in raw materials; uneven hardness, decarburization and coarse grains caused by improper heat treatment all reduce the fatigue strength of bolts. Many people mistakenly believe higher hardness is better. In fact, excessively high hardness lowers the bolt's toughness and speeds up fatigue crack propagation. A proper balance of strength and toughness is the key to fatigue resistance.
Fatigue Combined with Corrosion (Corrosion Fatigue) When bolts are exposed to humid, salt spray, acidic or alkaline environments, pitting pits form on their surfaces. These pits act as natural notches. Combined with alternating loads, they lead to corrosion fatigue. The coupling of corrosion and vibration sharply shortens the fatigue life, which deserves special attention for coastal and offshore projects.
Assembly and Structural Issues Uneven contact surfaces or tilted bearing surfaces subject the bolt to additional bending stress; Mismatched material combinations bring inconsistent thermal expansion and contraction, resulting in continuous preload fluctuation during operation; Lack of anti-loosening measures causes drastic load variation once the connection loosens. Bending stress is far more destructive to bolt fatigue than pure axial tension.
3. Typical Fracture Features for Quick Failure Identification
✅ Fatigue fracture surface: Generally consists of a fatigue source zone, crack propagation zone and final rupture zone. Shell-shaped or beach mark patterns can be observed, with no obvious elongation before fracture.
❌ Overload tensile fracture surface: Shows obvious necking and plastic deformation, with a rough fracture surface from one-time force damage.
By examining the fracture morphology of failed samples, you can make a preliminary judgment on whether fatigue failure has occurred and avoid misjudging it as unqualified material.
4. Engineering Solutions to Prevent Bolt Fatigue Fracture
Prioritize bolts with optimized thread root radius to reduce stress concentration at thread roots; protect surfaces from scratches and dents during machining and transportation. Control preload strictly in accordance with specifications using torque wrenches or torque-force measuring instruments to avoid insufficient preload or over-tightening. Avoid bending loads on bolts in structural design and ensure flat mating surfaces. Select suitable materials and heat treatment processes according to working conditions to balance strength and toughness. For corrosive environments, adopt corrosion-resistant materials (316L, 2205, etc.) or anti-corrosion coatings such as Dacromet to guard against corrosion fatigue. For vibration and alternating load conditions, deploy proper anti-loosening solutions (thread-locking adhesives, anti-loosening washers, etc.) to prevent connection loosening.
Summary
Bolt fatigue fracture is essentially slow crack propagation failure induced by alternating loads coupled with stress concentration. Its hazard lies in the absence of obvious warning signs. Even if a bolt meets strength requirements, fracture risks still exist when stress concentration, out-of-control preload, continuous vibration or corrosion interference are present. Effective control during product selection and assembly can eliminate hidden fatigue failure risks from the source.







